Search:

Type: Posts; User: jdixon1983

Page 1 of 2 1 2

Search: Search took 0.03 seconds.

  1. Yeah if you look up other exploded views of...

    Yeah if you look up other exploded views of vehicles with the 2075 servo, the part used is 2575 3x6 screw. I'm calling traxxas tomorrow, I think that's my issue.
  2. Ok so the part number for the screw that traxxas...

    Ok so the part number for the screw that traxxas lists that goes into the Horn is 2582 and lists 3x6 bcs on the exploded view. But when you look up part number 2582 on traxxas website and...
  3. Stampede 4x4 Vxl servo pulling to left when turned on.

    So an odd issue I can't seem to solve. The screw that traxxas has going into the servo to hold the horn down seems long. When I try to put it in the servo it starts clicking. I tried a smaller screw...
  4. Replies
    1
    Views
    206

    LOL ERevo on 3s power

    So I bought 2 3s lipos and ran it today. I hit a bump doing 70 and well I broke a front driveshaft and bent a front turn buckle and broke a rear turn buckle too. So what upgrades is everyone running...
  5. Replies
    3
    Views
    259

    Omg can't believe I did this

    So I just bought a bunch of parts to rebuild my Pede 4x4 Vxl after crashing it into a skate park pole and redecorating the front right side of the truck. So I get it all rebuilt and got in the...
  6. Replies
    1
    Views
    221

    Steering servo setup.

    So I bought a new servo horn and steering linkage. Anyone have a pic on setup. Do I use horn A? The exploding view does show what screws.
  7. So my son informed me that he got the truck stuck...

    So my son informed me that he got the truck stuck and was trying to get it unstuck with the controller. He tells me its more fun than walking over and picking it up an moving it!!! I took the cover...
  8. Day old Erevo making terrible grinding noise when throttle is applied

    So my sons day old Erevo 1/16 is making a terrible noise when the throttle is applied. It sounds like it's coming from the pinion and spur and the tires barely move. Any ideas on what he did?
  9. Replies
    4
    Views
    408

    Stampede rolling a lot

    So I just bought a pede 4x4 and I have the 4000 mah 2s lipo on it but boy does it roll a lot just bashing around. Can I solve this issue by lowering it a bit or is more needed? I would like to get a...
  10. Replies
    6
    Views
    835

    I just ran it through the truck again with no...

    I just ran it through the truck again with no issues and LVC worked at 3.2 volts this time so I think I'm ok
  11. Replies
    6
    Views
    835

    About a week old. I just bought the truck last...

    About a week old. I just bought the truck last week. Only second run
  12. Replies
    2
    Views
    532

    Parts needed for stampede telemetry

    Hey guys was wondering if anyone has the docking base and telemetry setup? What would I need to get my stampede 4x4 working with telemetry.
  13. Replies
    6
    Views
    835

    I just balanced the pack when I charge it. I do...

    I just balanced the pack when I charge it. I do every time I charge. It charged to 4.2 volts without a issue so I'm hoping its ok.
  14. Replies
    6
    Views
    835

    Lipo Voltage

    Ok so I was just out bashing with my stampede 4x4 and the LVC shut the truck down. I came and put it on the charger and one cell on the 2S traxxas 4000 mah lipo read 2.93 volts. It's charging right...
  15. Stampede Entered 1st stage of thermal shutdown!!!!

    Ok so I was running the stampede 4x4 today and everything is pretty much stock. I also have a 2wd slash. I run these two trucks with two different lipos. The first one i use are spc 5000MAH 2s 20c...
  16. Replies
    3
    Views
    297

    Do u want to change both pinion and spur right?...

    Do u want to change both pinion and spur right? If so take the dust cover off the gears held on with two screws. To take the pinion off u remove the small screw in it holding it to the motor shaft....
  17. Thanks for the info guys. Well Im only out a...

    Thanks for the info guys. Well Im only out a nylon locknut. Although I don't have any spares I gotta take one from my new stampede 4x4
  18. Threadlock? Was i suppose to put something on it...

    Threadlock? Was i suppose to put something on it when i put it back on? I never have and this has never happened before.
  19. Wow left Rear Tire came off while running!!!

    Wow well Idk what happened but i was running with a 2s lipo in and the left tire came flying off and rolled down the road. This has never happened to me before and now i lost the nylon nut that...
  20. Replies
    1
    Views
    256

    Spur and Pinion Help

    OK so I just put the tranny back together on my slash. I sheared the pin off the shaft!!! hehe. Anyway Im trying to setup my spur and pinion again and I think i got it I Just wanted to make sure...
  21. Ok thanks guys I got it!!!

    Ok thanks guys I got it!!!
  22. Yes that pin. I got one side in but I have been...

    Yes that pin. I got one side in but I have been working on this second one forever!!!!
  23. Cant get the tiny screw that holds the axle to the transmission to go in please help!

    Ok so i described it as best i can in the title. I got one in and it looks like everything lines up but i cant get the threaded part to screw in. Am I doing something wrong? I took the tranny apart...
  24. Thread: Charger ???

    by jdixon1983
    Replies
    9
    Views
    454

    I bought the Dynamite Ultra. Of course its kind...

    I bought the Dynamite Ultra. Of course its kind of Pricey at $130 but its an 8 amp charger and will charge and balance lipos and charge nimh and has a built in balancer.
  25. Replies
    1
    Views
    308

    Ok so I have to pull the transmission apart to...

    Ok so I have to pull the transmission apart to fix and I have everything apart except the axles. I can see the gears but it won't come apart. Am I missing a screw? Any help would be appreciated...
Results 1 to 25 of 40
Page 1 of 2 1 2