Search:

Type: Posts; User: larsen8

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. All done! I do need to get rid of those twisty...

    All done! I do need to get rid of those twisty ties as they look hideous. Otherwise a very clean, reliable and well-performing setup on this Summit. Ready to go back to brushless again someday.
    ...
  2. I'm also running an external voltage...

    I'm also running an external voltage checker/alarm because I've had issues with the LVD on the EVX-2 cutting in way too early. Eventually, I will find a good, clean, permanent way to waterproof the...
  3. Also running a dewalt motor with the proper caps...

    Also running a dewalt motor with the proper caps added and switched over to higher quality bullet connectors for the motor leads.
    ...
  4. Cover installed and bolted down. Wiring is very...

    Cover installed and bolted down. Wiring is very secure and very clean
    ...
  5. Now you can see all the wires folded over in the...

    Now you can see all the wires folded over in the box and packed in. The small electronic on/off switch is packed at the bottom beneath all the other wires. Apply some silicone grease to the foam...
  6. I've tapped a positive and negative lead into the...

    I've tapped a positive and negative lead into the battery leads on the ESC. These then run to a on/off switch and then to the BEC. Please excuse the twisty ties on the switch leads.
    ...
  7. External YEP 20A BEC that runs everything besides...

    External YEP 20A BEC that runs everything besides the motor. Overkill for this truck really. But it fits nicely in the spot where the secondary servo used to be. It has two separate output power...
  8. JST Y harness for plugging in the roof lights. ...

    JST Y harness for plugging in the roof lights.
    ...
  9. Electronic on/off switch plugged into CH3 slot. ...

    Electronic on/off switch plugged into CH3 slot. It's got a receiver plug on one end and a +/- power lead on the other end. I used CH3 because on this radio CH3 is just a button. So every push of...
  10. Here you can see how all the wires route up and...

    Here you can see how all the wires route up and into the RX box. Most of the wires route around front of the transmission and then up. You can see the JST plug underneath the other wires. That is...
  11. With the receiver box installed you can see all...

    With the receiver box installed you can see all of the wiring held in the clamp and ready to be plugged in. In order from left to right: CH2 ESC (with red power wire removed), power and ground wires...
  12. Replies
    2
    Views
    432

    Correct. It is a JST. They can be purchased...

    Correct. It is a JST. They can be purchased unassembled or with leads already attached on. I prefer to buy them unassembled because the crimping job on the assembled ones is usually very poor and...
  13. And a couple more... ...

    And a couple more...
    ...
  14. And some more... ...

    And some more...
    ...
  15. GT-5 Radio Upgrade, Improved Receiver Box, Electrical Modifications

    Hello,

    I thought I would start posting some of the modifications (specifically to the electrical system) that I've done to my Summit over the past few years for others to reference if they are...
  16. Replies
    17
    Views
    3,501

    Hello everyone. Just want to throw a quick...

    Hello everyone. Just want to throw a quick update out there. I've been very involved with other machining projects and life events for a while now so the Summit diffs have been forced to take a...
  17. Replies
    17
    Views
    3,501

    Time frame is looking to be a bit out there. I'm...

    Time frame is looking to be a bit out there. I'm likely not going to even start modeling anything much less producing prototype parts until at least after Christmas. Things are kinda busy right now...
  18. Replies
    17
    Views
    3,501

    Larger ring and pinion is absolutely in the...

    Larger ring and pinion is absolutely in the works. That's essentially the whole point of the project. To get a true 1/8 scale diff in there without losing the locking ability. This was likely...
  19. Replies
    17
    Views
    3,501

    Alright. Let's see if I can shed some light on...

    Alright. Let's see if I can shed some light on this bees knees. I am the one spoken of above and I do have some ideas browning in the oven of my mind.
    I'm currently brainstorming ideas for...
  20. Replies
    64
    Views
    6,867

    This is an incredibly late reply and you have...

    This is an incredibly late reply and you have likely already found the answer to your questions. But, here goes:
    I was running the double orange springs and 70wt oil all the way around at the time...
  21. Replies
    64
    Views
    6,867

    They are indeed bead locks. Axial Rocksters with...

    They are indeed bead locks. Axial Rocksters with Proline Moab XL's. Still running these tires two years later.....
  22. Replies
    57
    Views
    14,371

    Apparently the rules have not changed.

    Apparently the rules have not changed.
  23. Replies
    57
    Views
    14,371

    I take that back. My BEC can handle up to 12s...

    I take that back. My BEC can handle up to 12s lipo input. I don't know if forum rules have changed regarding posting other name brands, but I am using a ********* YEP 20A HV SBEC.
  24. Replies
    57
    Views
    14,371

    Yes, there is 4s input on the BEC. My BEC can...

    Yes, there is 4s input on the BEC. My BEC can handle up to 6s I believe.
  25. Replies
    57
    Views
    14,371

    Yes, that is absolutely right. However, I don't...

    Yes, that is absolutely right. However, I don't think having that extra negative wire there would do any damage. But I'm not sure on that so don't quote me.

    Also, I recently wired up my Summit...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4