Search:

Type: Posts; User: TwoBelugas

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Thread: 6s maxx!

    by TwoBelugas
    Replies
    19
    Views
    310

    Sidewinder 8th is 6s capable. But at that cost...

    Sidewinder 8th is 6s capable. But at that cost might as well spend another 20 bucks and get a MM2 with much higher amp limit and features.
  2. Replies
    28
    Views
    380

    Stiff. They work fine even with the heavy steel...

    Stiff. They work fine even with the heavy steel cage they make.
  3. You are right, This is a Poseidon, but I was...

    You are right, This is a Poseidon, but I was adventurous and got the 3000kv version since I planned on using high c SMC 4s packs. The thing is scary when you blip the throttle even lightly when...
  4. Got bored with my XO-1ish Rustl4r so moved the...

    Got bored with my XO-1ish Rustl4r so moved the parts over to this chassis to take advantage of the aero of the Deltaplastik body. Used a piece of 1/4 inch ABS plastic as base to bolt the RPM mmx page...
  5. Got the ESC bolted down good. Got an XT90 adaptor...

    Got the ESC bolted down good. Got an XT90 adaptor so it stays put and so I can use my SMC 4c packs.

    https://live.staticflickr.com/65535/50858078708_93d467499b_b.jpg
  6. Replies
    15
    Views
    214

    Which castle combo is mamba x+1510?

    Which castle combo is mamba x+1510?
  7. Replies
    43
    Views
    2,323

    Yeah I agree, if I was lucky enough to have the...

    Yeah I agree, if I was lucky enough to have the chassis you have I would choose the original bumper too. I have a couple of spare fast lane rustler chassis around but they don’t have the “it” factor...
  8. Replies
    43
    Views
    2,323

    The pro2 bumper is a good one, the other two I...

    The pro2 bumper is a good one, the other two I can think of is the rpm rustler bumper and the t bone rustler bumper.
  9. Oh.....I had no idea it’s three piece...

    Oh.....I had no idea it’s three piece design...ordered!
  10. Replies
    26
    Views
    653

    Yawzers. 9???

    Yawzers. 9???
  11. Replies
    26
    Views
    653

    Rc tech and arrmaforum have a number of people...

    Rc tech and arrmaforum have a number of people who say they have puffed SMC packs over the years.

    I haven’t personally had any issues with my SMCs.
  12. I have been staring at the front end and I think,...

    I have been staring at the front end and I think, with a little heat, one can bend the front skid plate more vertical and remove one or more of the pieces that connect the front bumper bar to the...
  13. Those satin parts sure add up quick. It’s pretty...

    Those satin parts sure add up quick. It’s pretty easy to spend a grand on an UDR before you even touch the electronics

    I actually have never bought a complete UDR, I ended up getting the parts...
  14. Yeah, in retrospect cutting right in front of the...

    Yeah, in retrospect cutting right in front of the fuel cell would be better as that allows the rear bumper to stay intact and makes for a better tail end structure. The way I did I cannot bolt the...
  15. Well, it’s happening. I will eventually sand down...

    Well, it’s happening. I will eventually sand down the cut areas to look cleaner.

    A crossmember was added for rigidness right where the rear sway bar would be since that’s the lowest point near...
  16. Replies
    7
    Views
    550

    1256 is 277. Not the most powerful one out there...

    1256 is 277. Not the most powerful one out there but a huge upgrade from stock and not to pricey. Have one in my builder udr and and another going into my next UDR base build.
  17. Replies
    7
    Views
    550

    Hot racing and GPM both make aluminum steering...

    Hot racing and GPM both make aluminum steering rack for the UDR that include a sturdier servo saver. Iím surprised they are not more talked about, money way better spent than most of the shiny bling...
  18. Replies
    18
    Views
    382

    Hot racing makes a spool for the Sl4sh diffs. ...

    Hot racing makes a spool for the Sl4sh diffs.

    https://www.amainhobbies.com/hot-racing-slash-4x4-lock-differential-posi-spool-hrasslf125/p649747
  19. The “pumpkin” is definitely a clearance killer...

    The “pumpkin” is definitely a clearance killer for morphing the udr into a rough terrain rig. There are a couple of other hang ups that I see too. In no particular order

    -the front end needs to be...
  20. The easier you are on the throttle the longer...

    The easier you are on the throttle the longer they last.
  21. Replies
    9
    Views
    399

    Well, you know some things are going on when you...

    Well, you know some things are going on when you capacitors that big in a Rustl4r.

    My uneducated guess to the bumper tease combined with the PL adjustable Sl4sh mount is that you are using a...
  22. Luckily I think the Marton bro kits rely mainly...

    Luckily I think the Marton bro kits rely mainly on longer length arms and different shock towers to achieve longer travel, at least on the 2wd kit, so they come with longer camber link and turnbuckle...
  23. This is how one knows squeegie is the resident...

    This is how one knows squeegie is the resident slash-encyclopedia. Lol. I didn’t even notice that.
  24. Thatís right, you did mention the customizable...

    Thatís right, you did mention the customizable shaft length with MIP in the other thread.
  25. Those 4wd kits have been preordering for awhile...

    Those 4wd kits have been preordering for awhile now so I got curious and asked them, it appears those guys don’t put out half baked stuff so they are still at it. When they do come out I hope MIP can...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4