Search:

Type: Posts; User: MindBlown

Page 1 of 10 1 2 3 4

Search: Search took 0.04 seconds.

  1. Or if you want a cheaper option, go with the...

    Or if you want a cheaper option, go with the sidewinder 4. They fixed the heat problem on 3S with a bigger fan, and the motor can go up to 6S too.
  2. Replies
    29
    Views
    5,474

    I would get the new E-Revo 2.0 if I were you. It...

    I would get the new E-Revo 2.0 if I were you. It has very durable components, 4WD, and awesome tires. I think it'll be available in a few days - on the page it says it will be available Late February.
  3. You cannot use the new iD batteries with you...

    You cannot use the new iD batteries with you charger, because the new iD batteries do not have separate balance connectors - they are in the connector themselves. But the good news is: you can buy iD...
  4. Replies
    345
    Views
    46,109

    $589 isn't too bad... I might just get one of...

    $589 isn't too bad... I might just get one of these... they used to sell the old e-revo for well over $600 and the prices since then have come a long way down..
  5. Replies
    5
    Views
    280

    They should be fine - I would get some XO-1 diffs...

    They should be fine - I would get some XO-1 diffs if they break though.. those are even tougher than the stock slash 4x4's I've heard..
  6. Off-road you say? The chassis you choose may...

    Off-road you say? The chassis you choose may depend on what kind of terrain you're running on.. Both of the chassis have good ground clearance, but if you need more, then I would go with the HCG...
  7. Replies
    18
    Views
    551

    I think you should go with the Rustler body and...

    I think you should go with the Rustler body and put some really big tires on it - Proline Mashers maybe... that would look AWESOME. You may or may not break the driveshafts so I would definitely gear...
  8. Replies
    18
    Views
    551

    Maybe you could get a rustler body on a...

    Maybe you could get a rustler body on a stampede.. I would buy some rustler body mounts and the rustler body (pre-painted if you want). That's my idea.
  9. Replies
    16
    Views
    1,822

    Thank you so much, that helps a ton. I am getting...

    Thank you so much, that helps a ton. I am getting the Traxxas Link module and a dust cover. Hopefully it helps.
  10. Replies
    16
    Views
    1,822

    Okay, so there might be a problem with the temp...

    Okay, so there might be a problem with the temp sensor - the clear tube on the temp sensor wire goes all the way back to the ESC, and I watched a video on youtube, and it was all the way up by the...
  11. Replies
    12
    Views
    1,078

    I've 3D printed a front and rear wing, some rims,...

    I've 3D printed a front and rear wing, some rims, and a shorty pack adapter for my Rustler with Bridge Nylon. Sure, these parts may not be the best and may break a little easier than other strong,...
  12. That's awesome. I bet if you got a fan for the...

    That's awesome. I bet if you got a fan for the XL-5HV then it would be an absolute beast.

    Here's my idea: Put a Titan 775 motor in your slash. That motor can handle 4S in a summit, why not in a...
  13. Replies
    16
    Views
    1,822

    That makes sense - I still have stock diff oil in...

    That makes sense - I still have stock diff oil in my diffs.

    I'll check the motor temp sensor and see if that's the problem. I'll keep y'all updated.
  14. Replies
    8
    Views
    632

    Do you need the Traxxas Link module to update the...

    Do you need the Traxxas Link module to update the firmware?
  15. Replies
    17
    Views
    851

    You got it ;)

    You got it ;)
  16. Replies
    8
    Views
    632

    That's happening to me some, too. How much did...

    That's happening to me some, too. How much did you dial your TSM to? Try recalibrating the transmitter to the ESC. Make sure nothing is in the way of the driveshafts or drive cups.
  17. Replies
    19
    Views
    1,240

    What I do every time I get a new RC car is tape...

    What I do every time I get a new RC car is tape the holes inside of my tires with blue painter's tape (duct tape works fine too). That way, water and dust cannot get into the tires so I don't have...
  18. Thread: Going big!

    by MindBlown
    Replies
    11
    Views
    778

    I've had mine for a couple of weeks too, and it...

    I've had mine for a couple of weeks too, and it works amazing! I recommend re-calibrating the transmitter to the ESC after your first run, though, because mine wasn't getting enough power until I did...
  19. Replies
    8
    Views
    484

    Honestly, venom batteries are not that good at...

    Honestly, venom batteries are not that good at all. Their customer service is really bad, too. If you want a really good and cheap battery, I would get an SMC or Floureon battery.

    Was the river...
  20. Thread: Rusty Balls

    by MindBlown
    Replies
    1
    Views
    468

    Have you been running in lots of water, because...

    Have you been running in lots of water, because that could be the problem.

    Take them out and put some good ol' WD-40 on them. That should help with the rusting.
  21. Replies
    16
    Views
    1,822

    How did you know it was the motor temp sensor?...

    How did you know it was the motor temp sensor? Was one of the ESC lights blinking?

    Also, this may be the problem (or just a dumb question), but are the front wheels supposed to spin a little more...
  22. Replies
    3
    Views
    334

    One question (I'm just curious): How does the...

    One question (I'm just curious): How does the nitro get the front caster angle down to 25°? I'm trying to model a 0-5° bulkhead for my rustler for on-road driving in Fusion 360.
  23. Are you talking about an old Velineon 2-pole...

    Are you talking about an old Velineon 2-pole motor or the new 4-pole motor? They all should be compatible with the slash, because they haven't really changed the mounts over the years, and they...
  24. Replies
    35
    Views
    3,711

    What did you print the mount with? PLA and ABS...

    What did you print the mount with? PLA and ABS become very brittle in low temps, but the ESC may help with that a little. PLA starts to deform (or has a glass transition temperature) at ~60°C...
  25. They do have brake disks on the nitro cars, and I...

    They do have brake disks on the nitro cars, and I would imagine they would also do it on this vehicle because of its weight and inertia from braking really hard. It may help with all of the stoppies,...
Results 1 to 25 of 250
Page 1 of 10 1 2 3 4