Search:

Type: Posts; User: olliec

Page 1 of 2 1 2

Search: Search took 0.02 seconds.

  1. Replies
    10
    Views
    1,085

    I've checked the servo end points and they are...

    I've checked the servo end points and they are fine.
    Anyone have any other ideas?
  2. Replies
    10
    Views
    1,085

    Steering Problem

    I've upgraded to a single Savox steering servo and ever since I've been constantly breaking parts of the steering.
    I was snapping the plastic steering arms so upgraded this to an HR aluminium one...
  3. Replies
    17
    Views
    2,567

    First thing I upgraded on mine were the rear...

    First thing I upgraded on mine were the rear springs to double orange to help stop the rear sagging so much.
    Then tyres were next. Tyre choice is very dependant on the type of terrain you'll be...
  4. Replies
    21
    Views
    2,022

    Gotta say I love the monster X and 2200kv...

    Gotta say I love the monster X and 2200kv sensored motor upgrade I did to mine.
    Its been swimming and caked in mud then hosed off when finished and so far I've have no problem with the upgrade. ...
  5. Thread: Melted wiring

    by olliec
    Replies
    18
    Views
    2,166

    So been out for quite a few run since getting...

    So been out for quite a few run since getting everything up and running again.

    After the first few runs I changed the voltage to 7.4v and installed a washer in the servo saver. This made a massive...
  6. Thread: Melted wiring

    by olliec
    Replies
    18
    Views
    2,166

    Thanks for all your help. It's very much...

    Thanks for all your help. It's very much appreciated.

    I've finally got it up and running again with everything working correctly.

    I directly soldered the red and black wire for the bec to the...
  7. Thread: Melted wiring

    by olliec
    Replies
    18
    Views
    2,166

    Just been looking more into connecting up the...

    Just been looking more into connecting up the power to the bec and now I think I might have got this wrong.

    At the moment I've soldered the bec wires onto the connector that is used for the...
  8. Thread: Melted wiring

    by olliec
    Replies
    18
    Views
    2,166

    I'm going to try and hook it up as per the castle...

    I'm going to try and hook it up as per the castle instructions. (Guess this is direct to the rx?)

    Don't have the means to make up any wiring.

    I've removed the red wire from the esc to rx and...
  9. Thread: Melted wiring

    by olliec
    Replies
    18
    Views
    2,166

    It just needed the esc re calibrating and is all...

    It just needed the esc re calibrating and is all working again. Happy days. Thanks so much for your help.

    Just got to get the bec wired up correctly now.
  10. Thread: Melted wiring

    by olliec
    Replies
    18
    Views
    2,166

    Sorry it's been awhile been a bit preoccupied...

    Sorry it's been awhile been a bit preoccupied with other stuff.

    So I've received the esc back from the shop and its still working ok.

    Have reconnected everything up again today but without...
  11. Thread: Melted wiring

    by olliec
    Replies
    18
    Views
    2,166

    So just fitted the new wiring harness and it...

    So just fitted the new wiring harness and it looks like I've killed the esc.

    All the lights front and rear are dim, when I flick the diff lock switch all the micro servos twitch and there's no...
  12. Thread: Melted wiring

    by olliec
    Replies
    18
    Views
    2,166

    Would that sort of set up for the individual...

    Would that sort of set up for the individual servos work for mine as I've only got a single steering servo?

    Also the 10amp bec only has one set of black and red wires.

    Just got the new wiring...
  13. Thread: Melted wiring

    by olliec
    Replies
    18
    Views
    2,166

    It's the 10amp cc bec and Mamba Monster X esc. ...

    It's the 10amp cc bec and Mamba Monster X esc.

    It was the brown wire running from the esc to the receiver that melted.

    I've connected the red and black wire for the bec to a power tap on the...
  14. Thread: Melted wiring

    by olliec
    Replies
    18
    Views
    2,166

    Melted wiring

    I don't know what I've done wrong but I need some help please.

    Just fitted fitted a new steering servo and CC BEC.

    Though I had wired everything up correctly but when I connected the 1st...
  15. Thread: No steering

    by olliec
    Replies
    8
    Views
    897

    That's good to know it'll handle dual servos if I...

    That's good to know it'll handle dual servos if I ever feel the need for more steering power.
  16. Thread: No steering

    by olliec
    Replies
    8
    Views
    897

    Ok great thanks for your help. Will the...

    Ok great thanks for your help.

    Will the castle creations 10amp bec work ok with the Savox SW1210SG ?

    Will I need to upgrade anything else?

    Thanks
  17. Thread: No steering

    by olliec
    Replies
    8
    Views
    897

    Was looking at getting a single Savox SW1210SG....

    Was looking at getting a single Savox SW1210SG. Would this be powerful enough to use only a single servo?

    Would it be better sticking with the dual servo setup? I do like to do a lot of rock...
  18. Thread: No steering

    by olliec
    Replies
    8
    Views
    897

    Thanks for the reply The throttle and all...

    Thanks for the reply

    The throttle and all other servos are working fine its just the steering servos that dont.

    I've tried swapping the servos as described but still no joy so I'm guessing...
  19. Thread: No steering

    by olliec
    Replies
    8
    Views
    897

    No steering

    Took the summit out for a walk last week and the steering stopped working.
    Took the receiver apart and noticed that there were signs of water ingress so ordered a new receiver.
    Just fitted the...
  20. Replies
    5
    Views
    690

    Wonder it might have been packaged wrong and is...

    Wonder it might have been packaged wrong and is an e-revo one as the body is actually touching the bumper
  21. Replies
    5
    Views
    690

    Unfortunately throw the original in the bin when...

    Unfortunately throw the original in the bin when I removed it so can't compare the two.
  22. Replies
    5
    Views
    690

    Yeah already tried that

    Yeah already tried that
  23. Replies
    5
    Views
    690

    RPM Front Bumper Mount

    Just fitted a new RPM bumper mount and have noticed that the bumper is now about 2cm higher and about 2cm closer in to the body. Is this normal or should it be exactly the same as the original...
  24. Replies
    10
    Views
    3,155

    Yeah it's amazing. Can now go 2+ hours of...

    Yeah it's amazing.
    Can now go 2+ hours of trailing and a bit of flat out ripping about before I have to change the batteries.
  25. Replies
    10
    Views
    3,155

    I'm running a 2200kv motor. I put a link to the...

    I'm running a 2200kv motor. I put a link to the actual ESC/motor combo I got in one of my posts above.
    Still using the stock gearing as well and at the moment it seems just about perfect for what...
Results 1 to 25 of 30
Page 1 of 2 1 2