Search:

The camber might be ok at rest but it could be it is changing through the suspensions travel.

Sent from my moto g stylus (2021) using Tapatalk

Never mind, I thought this was the 2wd forum.



Sent from my moto g stylus (2021) using Tapatalk

I bought a few of those a couple years ago. If they're not available I can look if I still have one in a spare trans.

Sent from my moto g stylus (2021) using Tapatalk

That's probably what I had. Used them up, looking to buy some more. I'll check the parts listings.

Sent from my moto g stylus (2021) using Tapatalk

I have some "carriers?" that use a smaller diameter outer pins to connect the the front arms. What are they used on? I thought Bandit but with the drag cars I've built they all use the same pins as...

I've mounted the Pro-Line sway bar behind the shock tower but that was on a Pro2 chassis. I've been trying to figure out a way to put a front sway bar on a Slash drag car (with no bumper) with Bandit...

I'm looking for some shock bushing similar to the STRC 3638-1 but non metallic. Anyone know of anything? Losi bushings fit kinda sloppy.

Sent from my moto g stylus using Tapatalk

That's what they're called in the parts list I have. I have some on hand, if they are coated steel then I'll use them.

Sent from my moto g stylus using Tapatalk

I'm building a metal case/ metal internals trans for a drag car. I am short a few washers that are for the input shaft and idler gear. I had some very thin steel washers in my trans parts bin that...

4wd front arms will not fit on the 2wd front.

Sent from my moto g stylus using Tapatalk

Our group allows 2s or 3s on the 2wd. The fast cars run the low turn motors with 2s, others are competitive with higher turn motors with 3s. Our rules are loosely following NPRC except for the...

Pro-Line made a front sway bar kit that looks a lot like that.

Sent from my moto g stylus using Tapatalk

Sorry to see you go, but in the future when things are better maybe you'll come back. I had one car (Kyosho Rampage) in the early 90's, 20 years later after closing my business which allowed me more...

I like the flex seal tape, good for reinforcing cracked bodies and great to prevent tire rubbing. It sticks too, I went to remove some and had to grip it with a pliers to get it off.

Sent from my...

I didn't read the entire thread but along with a good brushless motor/esc I would recommend a 50c or higher rated battery to work in conjunction with the higher performance brushless system to really...

Definitely spend some time with different weight oils to tune your suspension, shock mounting is important also, meaning the angle your shock is operating at. Pistons can be changed also to get the...

There is a way to repair the antennae, I remember seeing this discussed before. All you need to do is strip back the wire similar to the way it was before. Losing a small amount of the antennae is...

I've only seen this happen when the polarity was reversed or the esc was previously damaged.


Sent from my moto g stylus using Tapatalk

I've always thought about making a tool for this job. Frustrating, especially when the parts go flying away and get lost

Sent from my moto g stylus using Tapatalk

I made some cradles out of scrap 6" wide aluminum, it was diamond plate so I had to heat up the areas where I bent it to keep the metal from cracking. Two vertical mounting screws to attach it to a...

I don't use them as a work stand but I guess you could, a Blue Bunny ice cream container flipped upside down. I use them to store "work in progress" cars in my basement on.

Sent from my moto g...

These HRB batteries I have are as follows, 11.1 v, 5000mah 50c is 155x48x24mm. The 7.4 is 5000mah 50/100c 155x48x16mm.

Sent from my moto g stylus using Tapatalk

I'll get the specs off them and see if I can remember where I got them. Probably ebay.

Sent from my moto g stylus using Tapatalk

I have some 2s HRB packs that were thin enough to fit in the battery tray stacked with the optional tall battery hold down kit to hold them securely.

Sent from my moto g stylus using Tapatalk

Those are for a 2wd Slash, wide ones are in the front. Had you bought them for a 4x4 Slash they would all be the stock 5.5mm width. What width is on a Hoss, that I do not know. If you use the 7mm on...