Search:

Type: Posts; User: BrockFerens

Page 1 of 4 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    35
    Views
    775

    Have a question is the rear hub for the axle...

    Have a question is the rear hub for the axle shaft a 5mm or 6mm, sorry for hijacking thread

    Never mind found out. Thanks
  2. Replies
    7
    Views
    332

    The rear bearing is stuck, but rotates smooth and...

    The rear bearing is stuck, but rotates smooth and feels good. Just the front one was bad. I will just use a compressor and blow it out. Thanks for the help boys.
  3. Replies
    7
    Views
    332

    Ok so leave the motor, just replace bearings....

    Ok so leave the motor, just replace bearings. Thanks!
  4. Replies
    7
    Views
    332

    Cleaning Castle 1515

    I have just taken the motor apart, am going to replace the bearings as the one on the output end is rough. I am wondering is it a good idea to clean the inside, the rotor and windings with electric...
  5. That was most definielty the problem, thought i...

    That was most definielty the problem, thought i tried every combo but had them backwards. Man did that confuse me. Thanks guys!!
  6. TQ Transmitter Trigger steers, Wheel Throttle

    I bought myself a TQi Rx, and before i researched if it was compabtable with my TQ Tx i tried everything to pair it. Now somehow i messed up my controls. With the original TQ Rx & TQ Tx when i turn...
  7. Did you just double stack them at the Spur than?...

    Did you just double stack them at the Spur than? Or where did you place the 2nd bearing.
  8. Bump. No one has anything? I am using the Slash...

    Bump. No one has anything? I am using the Slash slipper shaft. Have it currently on the hole close to the middle of the shaft. But have tried both. Still get the play. The whole assembley moves back...
  9. Am having this issue as well, tried both holes in...

    Am having this issue as well, tried both holes in the slipper shaft.
  10. Replies
    18
    Views
    1,039

    Slipper Upgrade

    So I have a Stampede converted to Slash but with the bigger tires. Run Sidewinder 8th combo on 4S and 3S. I had the Revo slipper in, with aluminum pads. It heated up melted my spur, and destroyed the...
  11. Replies
    21
    Views
    1,510

    I have the 8th 2200 and running 19/50 the motor...

    I have the 8th 2200 and running 19/50 the motor gets hot. 19/54 is where it stays nice. Running grass, pavement, dirt.
  12. Replies
    21
    Views
    1,048

    remove the screw from the servo, and pull arm...

    remove the screw from the servo, and pull arm off. Turn on truck and transmitter cycle servo left right. Center tires and put the servo horn back on.
  13. Replies
    9
    Views
    829

    Is there another transmitter that will do...

    Is there another transmitter that will do telemetry style stuff?
  14. Replies
    47
    Views
    2,698

    My advice is to use the stock plastic part umm...

    My advice is to use the stock plastic part umm the part that connects to the turnbuckle that connects to the steering horn. Its part of the bell crank. I left mine plastic as it allows it to slide...
  15. Replies
    21
    Views
    1,048

    If you google hudy setup guide. it is a pdf and...

    If you google hudy setup guide. it is a pdf and it will help you with some guidance in what everything means.
  16. Replies
    21
    Views
    1,048

    Your going to have alot of fun buddy, just wait...

    Your going to have alot of fun buddy, just wait until it get serious lol. I went from brushed to sct to sidewinder 8th in 2 months. Lots of wrenching, and learning in there as well. Reading on this...
  17. The teeth are smaller sure they are same...

    The teeth are smaller sure they are same material. Its like 48p compared to 32p ( only using it as an example )
  18. Thanks, trying for something other than those. My...

    Thanks, trying for something other than those. My LHS doesnt carry those, either. Leave for work Sunday evening and would like to bring my truck with me. Going to try home depot, anyone know the...
  19. Is there a nut i can use in replacement of the...

    Is there a nut i can use in replacement of the MIP one? I lost a MIP 17mm nut in a field today and none of my LHS have nuts that will fit.
  20. Replies
    5
    Views
    536

    Thanks. I think im going to go to hardware store...

    Thanks. I think im going to go to hardware store and see if i can buy a sleeved nut that fits. Cause none of my LHS seem to have anything that would work.
  21. Replies
    5
    Views
    536

    17mm MIP wheel nut

    So i was ripping in the field today, and a wheel falls off. Lost the wheel nut that comes with the MIP 17mm conversion. Do ineed the MIP ones or will any work?
  22. They are weaker, i blew mine and had to switched...

    They are weaker, i blew mine and had to switched them out. ( Diff Gears )
  23. Replies
    74
    Views
    2,279

    That will most definitely be the one i will get. ...

    That will most definitely be the one i will get.

    I was looking into data loggers, would anyone know the route to go for this? i have been looking at some of the graphs people get, and am...
  24. Replies
    74
    Views
    2,279

    so next is bigger batteries lol forgot i need a...

    so next is bigger batteries lol forgot i need a wheelie bar. Was going to go with a front bumber, but i enjoy the bumper less look.

    Also, has anyone tried the Protrac? is it durable?
  25. Replies
    74
    Views
    2,279

    Apart from the D8's where does one go?

    Apart from the D8's where does one go?
Results 1 to 25 of 99
Page 1 of 4 1 2 3 4