Tekin RX8/T8 2000kv on Kershaw Designs 4s 7000mah Lipo's pushing 40+ mph (On GPS) with stock spur and 20t pinion.
Typically run an 11t hot racing hardened steel pinion for pure crawling, also have the stock 14t and a 17t.
Dual Savox SA1230SG's 500 oz/inch EACH using the CC BEC
21 Nichia LED's 28 Lumen each total of 588+ Lumen powered by a 11.1v 3s 1200mah Lipo.
Black Rit-dye Chassis, Green Blaze Pastidip Exo-cage.
Trencher X's on Axial 8 Hole wheels, Also have cut w/ no foam Mudslingers on black Desperado's and stocker's of course.
Custom painted flat black summit body w/ silver on the underside to show through after scratching.
Avid bearing's in differentials and hubs, stainless steel drive shafts and custom drilled hardened steel spider gears cut from the output pinions you receive with the spider gear replacements. There's a few small things I left out but I think that's about it LOL......
This is what the LED's look like in action..I have added 3 LED's to the front bumper since so another 90 lumen. LOL (This is the old body.)
![]()
My version of the ProLine 73 Ford Bronco
![]()
Working hard to appear reasonably sane.
My Summit was my first land based rc that I bought new in 2009. Changes from original are a 14.4 Dewalt, HS65mg shift and t-lock servos, no slop tranny mod, lowered body and t-bone a arm skids. Ihave yet to grow tired of the original red body and Canyons so I keep it looking original.
My boys Summit I bought used in 2011. Basically stock except for a 14.4 Dewalt.
![]()
TRAXXAS SUMMIT w/ Sanwa M12
Tekin - T8 1550kv w/ 21T/68T gearing
Castle Creations - MMM 2
Traxxas - Alu Red Push Rods
Traxxas - Double Orange Rear Springs
Traxxas - E-maxx Slipper disks
Traxxas - Alu Red Toe Links (being installed)
Hot Racing - Alu Dual Heatsink motor mount
Hot Racing - Alu Motor Mount Heatsink plate
Hot Racing - Alu Rockers Multi point
TruckMonster.de - Alu Diffs (front & rear)
TVRRC - Chassis Brace
Pro-Line - Desert Militia Body
Pro-Line - New F-11 Wheels
Pro-Line - Trencher X tires
Traxxas - Red 17mm Hex w/Extra lock nuts
M.I.P. - E-Revo Center Drive Shaft
Integy - E-Revo Wheely Bar
Integy - Super Heatsink w/Nikita high speed fan
T-Bone - Front Bumper
*Home Made Center Line Battery Carrier (allows large size batts but raises COG, not shown will post later)
![]()
Last edited by ksb51rl; 06-18-2013 at 12:14 AM.
I changed the body from my red summit body to a red ford raptor and now a black ford raptor with b5 lights and summit roll cage![]()
Taking the shine off the t-bone center skid plate
My rock crawler and my summit I painted to look alike
Last edited by Dumbdizzal; 06-07-2013 at 01:08 AM.
She's getting tatty and been well used but I got her some new shoes anyway...
(Yea I know, toe an camber need sorting)
Summit LT - Summit FPV - Slash 4x4 Scale Raptor
My beast!
![]()
My Summit with trenchers
My Summit stock
![]()
This is my latest Summit, picked it up a few days ago for $150. Just needed a couple of parts to fix it,
Output shaft on the rear diff, and the servo that controls the rear locker.
And this was the broken part,
![]()
ERBE, ERBE, Summit, Slash 4X4, Bandit,
![]()
Jconcepts Raptor, Rc4Wd mud slingers, pro-line F-11 wheels, dewalt, traxxas 5352r slipper kit
Black paint pen run amok... lol
Send via most likely stolen wifi...
(RAH)² (AH)³ + [ROMA (1+MA)] + (GA)² + (OOH)(LA)²
Here is my Summit with a 56 Ford body I just finished painting
![]()
few action shots
![]()
crawl-bash-swim. The Summit does it all.
crawl-bash-swim. The Summit does it all.
My boys back together![]()
![]()
little bit of mudding:
![]()
crawl-bash-swim. The Summit does it all.
Some shots from last weekend.
[IMG][/IMG]
![]()
Working hard to appear reasonably sane.
crawl-bash-swim. The Summit does it all.
Yes, this IS a Summit![]()
Summit LT - Summit FPV - Slash 4x4 Scale Raptor
Last edited by saviobatista; 08-24-2013 at 10:40 AM.