Qc_maxx showing off (Lst2 diffs in an E-Maxx) Now with CC1717 in my modded 3906

[e-marc]

Beau setup Fred !

I will buy an e-maxx this winter , it will be my first electric i've had several nitro monter trucks .

[PowerToTheMaxx]

Nice.

Will the innards of a LST diff fit into any of FLM's combo/hybrid bulk systems? I know you could use the regular bulks and the pvc collars and sutch, but would they fit any of the other combo things, and are they tougher than FLM ultimate diff/bulk combos?

[EMaxx_Quebec]

E-marc, t'es d'ou au Qc..

I can't talk for FLM stuff since I didn't try any exept chassie!
Let's FLM gouru reponse to this.

[e-marc]

Je suis de la rive-sud , desolé du delais !

[nburns11]

What Kershaw designs driveshafts did you order

[EMaxx_Quebec]

I kept the stock one as non expensive fuse part.

[nburns11]

@emaxx_Quebec when ordering from Kershaw is the newer or older style emaxx driveshafts? I have a 3906 with the LST differentials and outer driveshafts. I have RCM 8mm drivecups on the diff's.

[EMaxx_Quebec]

I still buy the older one. Check post #3
few buck , and WITH MY STYLE of driving, not too much of breackage.

[EMaxx_Quebec]

Back at it guys!
HVL here I come!

[SnoopMaxx]

Oh Myy

[Silver5]

Christmas came early!

[PowerToTheMaxx]

THat is a lot... of... Shiny

[Emaxx Racer]

you're only missing two things- powerstrokes and ue steering assembly

[EMaxx_Quebec]

2 years of close eyes for dood deals!

[EMaxx_Quebec]

I didn't toutch my maxx for a long time gathered part,I score this for Under 200$ can recently!




So I'm back at it seriously!!
New diff case!!
new Chassy : UE HVL !

[rock-rod]

nice you scored some kmaxx cases too! I have two sets with one being used for my magneto and another as spares.

[blacktruth609]

Thanks

The diff ratio I have is 43/13 ( LST)but I run 51t mod 1 ofna spur with a 20t pinion.
You have to be careful to not chose 45/11 ( Muggy )

And now I have a bullet proof trans for any BL system

Few weeks ago I was able to put my hand on this!!!!!
New Ultramaxxed gear set and idlers
IMG]http://i265.photobucket.com/albums/ii216/Emaxx_Quebec/DSCF0003-2.jpg[/IMG]

Do you think these trans gears are still for sale?

[SnoopMaxx]

You can use the steel idlers from the 3908
Just have to grind the width a bit




And then replace the roll pin on the topshaft


You may find the bottom gears in aluminium but they are extremely rare

[EMaxx_Quebec]

[QUOTE=EMaxx_Quebec;3838076]With the agreement of “IT’S Me“ from RCM I post my step by step process to make this mod.

1: It will be cheaper if you have already:
- Center dog bone.
- 4 old and unused drive shafts. (replace 1/8 diff output shaft )

2: It cost me (include shipping cost to Canada):

- 2 x LST 2 diff = $43 us ( 43/13)
- 4 x 1/8 diff output shaft + 2 x Drive cup - 8mm bore for 1/8 diff = $50 us
- 1 Dog Bone center kit from Kershaw = $ 55
- Bow ½ pvc (Fem to Fem) + 1” join = $0.50

First, I cleaned the diffs and put Gorilla Swat in it and change the 4 diffs output.


When I put them back together and tighten the ring to the cup, it was impossible to turn the diff by hands.



I noticed that the RC monster output was a little bit too long so I had to shave them to the appropriate length. Once shaved the diffs output, it worked perfectly!!

[EMaxx_Quebec]

Next, plastic trimming can get started. It’s better to do it slowly to not take too much material at a time. I used this dremel bit to do all the work.


I hope the pictures talk by themselves.
A lot of small adjustments is needed to achieve a perfect fit.

[EMaxx_Quebec]

Just made the switch on some on my old photobucket for the LST2 diff swap!
Seem to be needed

[Forrest]

Not to steal your thread but I found this for people who may not to want to make them or do not have time. https://www.uninterrc.com/chooseyourbulkheads

[EMaxx_Quebec]

No, It, PERFECT!! those were not avaible in 2009! lool
But I got some meked for me by snoopmaxx in aluminium!
Save a LOT of time !

Nice one!