What did you do with your X-Maxx today?

[cash4rvs]

This tires are super, mate.

Like them a lot. Fun at full throttle trying to lay a strip of rubber on the concrete. These can be balanced
as close to zero expansion.

I’ve added so much alloy weight and with the Integy sway bars you have to really try for wheelies, stays planted and steers great. Using 50/19 right now.


Sent from my iPhone using Tapatalk

[Fboylstein]

Like them a lot. Fun at full throttle trying to lay a strip of rubber on the concrete. These can be balanced
as close to zero expansion.

I’ve added so much alloy weight and with the Integy sway bars you have to really try for wheelies, stays planted and steers great. Using 50/19 right now.


Sent from my iPhone using Tapatalk

Going three quarter throttle on dirt road, lost control crashed roof first into a large tree, five foot off the ground; hit end of guard rail with roof of truck causing a loud bang and guard rail to vibrate. Both hits no damage to xmaxx and both times direct hits on RPM roof skid protectors. Truck is tough and so is RPM. Also, slammed into a chain link fence, T-Bone front bumper did its job. Xmaxx is one tough truck!

[TechnoGears]

Jumped my stock one up a hill landed and blew seals off rear inner bearings now i'm waiting on parts to run again

[cgrant26]

Jumped my stock one up a hill landed and blew seals off rear inner bearings now i'm waiting on parts to run again

Stock carriers/bearings or the upgraded RPM or ProLine ones? If stock, replace them with the RPM or ProLine ones. Those anemic stock inner bearings just don't hold up very well.



If you go with RPM, don't forget to grease the bearings in the kit before you run them as they only ship with a little anti-corrosion oil in them.

[TechnoGears]

Stock carriers/bearings or the upgraded RPM or ProLine ones? If stock, replace them with the RPM or ProLine ones. Those anemic stock inner bearings just don't hold up very well.



If you go with RPM, don't forget to grease the bearings in the kit before you run them as they only ship with a little anti-corrosion oil in them.

They were stock carriers and bearings I cleaned it and flipped it around just blew off other side. Ordered my rpm ones already so waiting on those, I just still wanted to run my truck cause its a blast to drive around.

[CrazyXMAXX]

amazing Xmaxx
Week after week of thrashing with no failures
durability of a over 4 years of abuse
Can’t wait to beat ‘em again

Have you Loved your Xmaxx today

[ReglarGuy]

Week after week of thrashing.

With all that bashing, now I see whey they call you CrazyMaxx...you's crazy boss!

[CrazyXMAXX]

With all that bashing, now I see whey they call you CrazyMaxx...you's crazy boss!

What’s really Crazy ....




Political discussions are not allowed here.

[CrazyXMAXX]

Fun times

Escape reality- thrash a Remote Control Xmaxx

[95blackz26]

Fun times

Escape reality- thrash a Remote Control Xmaxx

i've done it with any r/c i've had but i take the xmaxx out and beat on it like it owes me money.

[Evolution37]

Street run for few minutes




Sent from my iPhone using Tapatalk

[95blackz26]

decided to clean and re-lube my axle carrier bearings since i had some spare time.

[Juanmacine]

Street run for few minutes




Sent from my iPhone using Tapatalk

Nice colour-line, mate.

[CrazyXMAXX]

All Xmaxx’s motor bearing maintenance achieved > dirty

Down an bound to test ‘em again

Most important bearing to keep
clean and lubed-is the motor bearing by the pinion
Most expensive to replace damage from a failed bearing
Bearing freezes up, then melts the plastic bearing carrier
wfo aluminum end cap $45+

When was the last time you had your motor apart

[Gosraider]

Yesssssssss



Enjoy
Gos

[95blackz26]

went out for a run with it the day after we got some snow. little bit of snow and a little bit of mud. equals i should have put it in the tub to dry out instead of my kitchen.

[CrazyXMAXX]

Ran 3 Xmaxx’s
Broke 1 rear output yoke

1 HRB 4s soft pack -small rock cell damage = failure
now running power hobby pro lipo “hard case”

Grip it and rip it

[95blackz26]

changed the diff bearings. 1 out the 4 actually moved, the rest were frozen. soaking the old ones in wd40 to clean them up and see if they are still good. so the truck should move a lot better now.

Traxxas has a strict language policy. A word filter operates to change inappropriate words to *s. When you see these in your post, you MUST edit them out. -ksb51rl

[zzuppr]

Took it to the woods


Sent from my iPhone using Tapatalk

[Chewbacca 3]

My second outing with the truck today. Discovered it just don't care if the grass is long!



There was some serious cleaning up to do once home though!

[95blackz26]

My second outing with the truck today. Discovered it just don't care if the grass is long!



There was some serious cleaning up to do once home though!

i bash my truck where i live which is an apartment built in a sand pit. it's true what they say. sand get's everywhere. i run it in the dirt/mud area and hard packed sand and if it's wettish sand i run it in that. but dry sand nope

[Chewbacca 3]

So the UK is in lockdown again at the minute, but we are allowed out to exercise. So, I took my truck for a walk to get some exercise. There's a great spot 5 minutes drive away, in the middle of nowhere. It was a bit muddy though after all the rain & the diggers working there. (Hope I'm not going to lose this place, it's so good for RC cars!) Found a few mounds of chippings where they have been clearing trees.


Truck needed a bath when I got home.



Sorry for the bad action shots, I can't shot & drive! How people get video while driving is beyond me.

[Gripdog7205]

So the UK is in lockdown again at the minute, but we are allowed out to exercise. So, I took my truck for a walk to get some exercise. There's a great spot 5 minutes drive away, in the middle of nowhere. It was a bit muddy though after all the rain & the diggers working there. (Hope I'm not going to lose this place, it's so good for RC cars!) Found a few mounds of chippings where they have been clearing trees.


Truck needed a bath when I got home.



Sorry for the bad action shots, I can't shot & drive! How people get video while driving is beyond me.

You did well. Just glad you got out and put in work. I use a GoPro and have a knock off as well for video. Good investment. In the speed run world one hand driving isn’t an option.


Sent from my iPhone using Tapatalk

[LT-Xmaxx]

Hey everyone im new to the forum, and New to Xmaxx for about 3 months now and ive been tinkering, modding, fabbing, and of course BaASHInG! Some things i did today was install stainless screws/painted krylon fusion red proloc rings, and did some tire lettering on the proline trenchers with silver sharpee.

[95blackz26]

is that stand custom made?

[LT-Xmaxx]

is that stand custom made?

Yes it's a custom one made from stainless scrap, some 1/2" thick rubber to keep it from slipping off, and a random piece with a bearing for the turntable use.

Sent from my SM-G955W using Tapatalk

[Juanmacine]

Hey everyone im new to the forum, and New to Xmaxx for about 3 months now and ive been tinkering, modding, fabbing, and of course BaASHInG! Some things i did today was install stainless screws/painted krylon fusion red proloc rings, and did some tire lettering on the proline trenchers with silver sharpee.

This stand looks excellent, good job.

[CrazyXMAXX]

$300 Xmaxx got servo metal gear upgrade 2087X
Been running atomic aluminum steering servo saver assembly on it
Didn’t realize at still had stock plastic servo gears

Beaten, put away muddy > Ready for More

[CrazyXMAXX]

Original 6s Xmaxx had a frozen dirty
bearing on a rpm carrier
All Cleaned- lubed - reinstalled
Ready for its thrashing

Get out there

[CrazyXMAXX]

The 300 dolla holla Xmaxx
Broke another left rear axle just out from the ball
Thrashin’ good an Twisted it loose

Beat it to enjoy it

[Chewbacca 3]

Left the X-Maxx home and took the Mini E-Revo.
Broke it.
Lesson learnt here, take the X-Maxx if there's a ramp.

[CrazyXMAXX]

The 8s Xmaxx had its rear center bearings serviced
After having bound up issues

Send it Lubed up

[LT-Xmaxx]

Installed some Amazon Special C-hubs/steering knuckles(4pieces for 1/4 the price of the name brands so i went for it). Everything fit, bearings fit perfectly, no issues while turning, only issues were a 1mm up/down play on the C-hub to steering knuckle pins (could be resolved with a shim), also if you look at the bottom of C-hub its alot different than the stock ones, probably suppose to only work with this brands aluminum arms.

Sent from my SM-G955W using Tapatalk

[95blackz26]

The Duratrax Banditos came in. Almost zero ballooning but heavier for sure.

Sent from my iPhone using Tapatalk

what kind of surfaces do you run on? how are they on loose material like sand?

[afreek1000]

Installed some Amazon Special C-hubs/steering knuckles(4pieces for 1/4 the price of the name brands so i went for it). Everything fit, bearings fit perfectly, no issues while turning, only issues were a 1mm up/down play on the C-hub to steering knuckle pins (could be resolved with a shim), also if you look at the bottom of C-hub its alot different than the stock ones, probably suppose to only work with this brands aluminum arms.

Sent from my SM-G955W using Tapatalk

Cool, they look nice. Are these the ones with triple bearings?

[LT-Xmaxx]

Cool, they look nice. Are these the ones with triple bearings?

Ya they are decent just utilizes stock bearing sizes though. But ya they aren't triple bearings, I think Vitavon makes the super beastly triple bearing ones, and maybe one other mfg. I can't remember.

Sent from my SM-G955W using Tapatalk

[CrazyXMAXX]

Found a failing trans shaft bearing on
the original 6s Xmaxx
when a new 19t/50t wide spur gear installed
running stock 8s tires again
18/54 was not as fun/fast on 1600kv 8s max6

Used motor bearing installed in the 8s Xmaxx
Replacement 6x17x6mm motor bearings ordered

Xmaxx released 5 years ago

[LT-Xmaxx]

Installed some new beefy goodies !
- Gpm Hardened stub axle hubs/with thicker axles.
- Area Rc rear Diff housing
- New diff Bearings.
- Outdrive Cup red silicone boot zip tied for now.
- shimmed rpm rear hub carrier bearings with aluminum foil tape as i noticed some play on housings when i checked the tire movement on the hub.
- more rpm hinge pins with nylon washers as the pack came with all the same length.
(The rear of the truck is super smooth, and all the sloppiness is gone)

Sent from my SM-G955W using Tapatalk

[Edgemoulic]

Hatchet X for playing all around


Sent from my iPhone using Tapatalk

[CrazyXMAXX]

Ran 3 Xmaxx’s
Broke 2
Proline servo linkage Upgrade for original 6s
Rear 5th scale silverback 5b baja rim failed=replaced

Wheelie city